- Hari ini aku belajar macamne nak configure cisco router 2600..Macamne nak configure?So, sebelum configure kita perlu ada:- Network design & kena tau interface mana dan ip mana yang nak diconfigure..Dan 'what we need to configure?':-
- Untuk membuka paparan antaramuka untuk proses configurasi:-
Start -> All Programs -> Accesories -> Communications -> HyperTerminal
Coding configure cisco router:
Router>enable
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
*********** Setup Hostname *************
Router(config)#hostname SHAF
*********** Start Setup Serial 0/0 Interface with DCE connection *************
SHAF(config)#interface Serial 0/0
SHAF(config-if)#ip addr 10.2.2.1 255.255.255.0
SHAF(config-if)#clockrate 64000
SHAF(config-if)#no shutdown
SHAF(config-if)#
00:08:29: %LINK-3-UPDOWN: Interface Serial0/0, changed state to up
00:08:30: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
SHAF(config-if)#exit
SHAF(config)#exit
SHAF#
*********** End Setup Serial 0/0 Interface with DCE connection *************
*********** Start Setup Fast Ethernet l 0/0 Interface *************
SHAF#config terminal
Enter configuration commands, one per line. End with CNTL/Z.
SHAF(config)#interface fastethernet 0/0
SHAF(config-if)#ip addr 10.1.1.1 255.255.255.0
SHAF(config-if)#no shutdown
SHAF(config-if)#
00:16:14: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
SHAF(config-if)#exit
SHAF(config)#exit
SHAF#
*********** END Setup Fast Ethernet l 0/0 Interface *************
*********** Check Interface fast Ethernet 0/0 Detail *************
SHAF#sh int fast 0/0
FastEthernet0/0 is up, line protocol is down
Hardware is AmdFE, address is 000d.28ef.bac0 (bia 000d.28ef.bac0)
Internet address is 10.1.1.1/24
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto Speed, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:23:34, output 00:00:04, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
**********************************************************************
Let setup FastEthernet0/1 at LAB_B router
**********************************************************************
SHAF(config)#int fast 0/1
SHAF(config-if)#ip addr 10.1.1.2 255.255.255.0
SHAF(config-if)#no shutdown
SHAF(config-if)#
00:29:54: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
00:29:56: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
SHAF(config-if)#
*********** End Of setup FastEthernet0/1 At LAB_B router *************
*********** Start Setup routing protocol using RIP ****************
SHAF(config)#router rip
SHAF(config-router)#network 10.1.1.0
SHAF(config-router)#network 10.2.2.1
SHAF(config-router)#
*********** End Setup routing protocol using RIP ****************
*********** Start Register IP host lookup table ****************
SHAF(config)#ip host LAB_A 10.1.1.1 10.2.2.1
SHAF(config)#ip host LAB_B 10.1.1.2 10.2.2.2
*********** End Register IP host lookup table ****************
